How To Disable Seat Belt Alarm Ford F150

Download Article

Download Article

It is common knowledge that you lot should wear your seat belt while driving. Yet, there are many situations where a factory seat belt alarm tin become a nuisance. For case, if you are driving on a farm at low speeds with many stops, yous may non need a seat belt. More than urban situations, such as taking your wallet out in a drive-through or letting your domestic dog ride shotgun, tin too exist unpleasant with a constant ding. Sometimes, information technology is fifty-fifty possible for the alarm to get "stuck" and ding constantly whether yous are buckled or non. Luckily, it is usually possible to disable this seat belt alert.

1. 1

   Beware of the airbag risk. On many cars, the seat chugalug sensor is also used to trigger the airbag. Investigate whether this is the instance on your machine earlier doing anything desperate to your seat belt alarm.

2. 2

   Check the user transmission or ask your reseller to disable information technology per software. Well-nigh all manuals give instructions on how to disarm the seat belt alarm without cutting any wires. This usually consists of doing a serial of tasks in the car while parked. As an case, the sequence for turning off the seat belt alarm on a Toyota Camry (2004 and newer) is given below.^[1]

   • Insert the primal and turn the power on. You should not crank the engine.
   • There is a knob on your dash panel that toggles your trip and total odometer readings. Press this knob until y'all see "ODO" on the musical instrument panel.
   • Yous should turn the key off, and and so back on.^[2]
   • Hold the same knob for 10-15 seconds. While still holding the knob, put on your seatbelt, and and then release the knob.
   • You should meet "B OFF" wink on the instrument panel. This indicates that you turned off your seat chugalug alarm.

   Advertisement

3. 3

   Disable your alarm. This may hateful following the steps in the owner's manual for reprogramming your alert, which, as described to a higher place, is often a series of actions taken while the car is parked.^[three] Alternatively, you can have the vehicle to your dealer to do this. Some vehicles may have to go to the dealer to exist reprogrammed with specific software.

   • It is worth noting that dealerships are ofttimes reluctant to fulfill this request due to legal and liability issues. All the same, this is the safest method of disabling your seat belt alarm, and dealerships will make reasonable adjustments in special cases.^[4]

Advertisement

1. 1

   Get an unattached seat chugalug prune if y'all don't programme to utilise the seat chugalug. There are two basic products on the market that are referred to equally a seat chugalug alarm stopper. The get-go is just an unattached seat belt clip that can be inserted into the receptacle. The safest style to utilize this pick is to source a seat belt clip, or tongue, that matches your original seatbelt exactly. Yous can look for ane at a scrap yard or parts store.

   • Measure the overall dimensions of the prune's exposed metal section, as well as the dimensions of your receptor.
   • Remember that driving without using a seatbelt is very dangerous, and against the police force in well-nigh areas.

2. ii

   Purchase an extender if you plan to employ the seatbelt. The other stopper option, chosen an extender, is a piece that clips into the receptacle, just also provides an boosted receptacle so that you can use your seat chugalug without removing the alarm stopper. You lot should purchase your extender from the original equipment manufacturer of the seat chugalug, and information technology must meet the criteria in its operating manual, including mass and stature.^[5]

   • Following the criteria for your extender is important because your seat chugalug system needs to pass an anchorage pull examination, which ensures that it can withstand crash-level forces. Y'all can find these requirements online or by request your seat chugalug manufacturer.

3. 3

   Install the seat belt alarm stopper. Make sure that your stopper fits your seat belt receptacle. And so, simply click the stopper into your receptacle. You are now free of the dinging alarm sounds.

Advertisement

Add New Question

• Question

  Tin can a seat belt cause the airbag light to always be on?

  

  Yes. To verify if they're connected, effort looking under your seat. The connector for the seat belt lock volition frequently be a bright color, and if yous see information technology, that means information technology's continued to the airbags. Notwithstanding, not all car models volition have this feature. If you're not certain, have your machine to the dealership or enquire your manufacturer.

Enquire a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertizement

• You lot might need a flashlight to see ameliorate nether the seat.

• Drive your vehicle later on to cheque if information technology worked; if you lot cut the wrong wires, just use butt connectors to re-connect them.

• Information technology should make no difference whether the belt was plugged in while you practise this, just it may exist different on the dissimilar varieties of vehicles.

Advertising

• Tampering with the seat belts will void your warranty.

• Do not attempt to cutting the buckle harness. This will likely disable the front passenger airbag. In some cars, cutting this cable will also have the opposite effect that y'all desire, forcing the seat chugalug warning to stay on constantly.

• Information technology'southward non recommended to attempt to bypass the alarm within the seat belt buckle. Some seat belts contain pyrotechnic devices that tin detonate if tampered with, and removing or tampering with the pieces inside can consequence in the seat belt releasing during a crash.

• Tampering with your seat belt sensor in any manner can affect airbag performance. This can put you and/or your passengers at serious risk. Be sure that your airbags will not be affected before altering your seat chugalug alert sensor.

Advert

Things You lot'll Need

Installing a Seat Belt Alarm Stopper

• Seat Belt Alert Stopper or Extender

Disabling the Seat Chugalug Alarm with Manufacturer's Tools

• Owner's Manual
• Software Update (if needed/bachelor)

About This Article

Article Summary X

To stop a seat belt warning from going off, you can purchase a seat belt alarm stopper at a fleck yard or from the manufacturer. One pick is to buy an unattached clip that is inserted into the seat belt receptacle and will stop the alert from going off. The other is an extender that provides an additional seat chugalug receptacle, which allows the user to fasten their seat chugalug while stopping the warning. To disable the alarm without cutting any wires, cheque the motorcar's user manual for instructions or ask your reseller to disable it using software. For more tips on stopping your seat belt alarm safely, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 746,462 times.

Did this article assist you?

Source: https://www.wikihow.com/Disable-a-Seat-Belt-Alarm

Share this post